Step-by-Step Guide to Disassembling a Classmate PC (Intel Magalhães)

Step-by-Step Guide to Disassembling a Classmate PC (Intel Magalhães)

Table of Contents

1. Introduction to Taking Apart a Classmate PC
2. Disclaimer and Potential Differences in Screws
3. Step 1: Removing the Back Cover
4. Step 2: Removing Screws in Recessed Holes
5. Step 3: Removing Screws Underneath the Battery
6. Step 4: Removing the Keyboard
7. Step 5: Taking Out the RAM
8. Step 6: Removing the Solid State Drive
9. Step 7: Disconnecting the Wireless Chip
10. Step 8: Removing the Gray Plastic Piece
11. Step 9: Removing Screws Securing the Metal Pieces
12. Step 10: Removing Screws Holding the Lid
13. Step 11: Removing the Wi-Fi Antenna Cables
14. Step 12: Removing Screws Under the Rubber Feet
15. Step 13: Disconnecting the Speaker Cable
16. Step 14: Disconnecting the Ribbon Cables
17. Step 15: Pulling Out the Motherboard

🔍 Introduction to Taking Apart a Classmate PC

In this guide, we will walk you through the process of taking apart a Classmate PC. Whether you're experiencing technical issues or simply want to explore the inner workings of your device, dismantling a Classmate PC can be an enlightening experience. However, it's essential to proceed with caution and follow the instructions carefully to avoid any damage. Let's dive in and learn how to disassemble this laptop-like device from First Team FRC,612.

❗ Disclaimer and Potential Differences in Screws

Before we begin, it's important to note that the Classmate PC from our team may have undergone previous disassemblies, which could result in differences in screws and other minor variations. Some screws may appear longer or shorter, and the configuration may slightly differ from what you see in this guide. In case you encounter any discrepancies, refer to your specific device and exercise caution when proceeding.

🔧 Step 1: Removing the Back Cover

To start the disassembly process, locate and remove the two screws securing the back cover of the Classmate PC. These screws are positioned to cover the motherboard from the back. Keep in mind that the size of these screws may differ slightly from what is shown in the video. Set the screws aside in a safe place.

🔧 Step 2: Removing Screws in Recessed Holes

Next, identify the recessed holes between the cover and the battery. Remove the three screws in these recessed holes. As Mentioned earlier, the size of these screws may vary, so ensure you are using the correct screwdriver. Set the screws aside for reassembly.

🔧 Step 3: Removing Screws Underneath the Battery

Underneath the battery, you will find three or four screws that also need to be removed. These screws secure specific components of the Classmate PC. Carefully remove these screws, making sure to keep them separate from the previously removed screws.

🔧 Step 4: Removing the Keyboard

The keyboard removal process involves two important clips located near the upper portion of the keyboard. Use two small screwdrivers or similar tools to press and release both clips simultaneously. Gently pry up the keyboard, ensuring it doesn't get caught on anything.

🔄 Pros: The Classmate PC's keyboard can be easily removed by following a simple clip-release mechanism.

🔧 Step 5: Taking Out the RAM

Once the keyboard is removed, you can access the RAM module. Remove the two screws that secure the RAM in place. Take extra care while handling the RAM module to prevent any damage. Set aside the screws for later use.

🔧 Step 6: Removing the Solid State Drive

The Classmate PC may also feature a solid-state drive (SSD) that can be removed during the disassembly process. Locate and remove the two screws holding the SSD in position. Make sure to store these screws safely for reassembly.

🔧 Step 7: Disconnecting the Wireless Chip

The wireless chip is connected to the motherboard by a cable. Carefully pull off the wireless antenna cable from the wireless chip using the appropriate tools. Exercise caution to avoid damaging the cable or chip during this step.

🔄 Pros: Removing the wireless chip enables easy access to other components of the Classmate PC.

🔧 Step 8: Removing the Gray Plastic Piece

To remove the gray plastic piece, use two wiggle tools or precision screwdrivers. Pry out the two clips at the back of the piece and then pry it off from the front. This will allow you to access other internal components of the Classmate PC effectively.

🔧 Step 9: Removing Screws Securing the Metal Pieces

Within the disassembled Classmate PC, you will find five screws: one in the center and two on both sides. These screws secure two metal pieces together, providing structural support. Remove all five screws using the appropriate screwdriver.

🔧 Step 10: Removing Screws Holding the Lid

Please note that if you are not planning to access the lid components, there is no need to remove the four screws on the lid. These screws are only Relevant when exploring the inner components of the lid. Avoid unnecessary disassembly to prevent any accidental damage.

🔧 Step 11: Removing the Wi-Fi Antenna Cables

With the lid removed, you will encounter the Wi-Fi antenna cables connected to the motherboard. Use needle-nose pliers or precision flathead screwdrivers to disconnect both cables carefully. Take your time during this step to ensure a smooth removal process.

🔄 Pros: Removing the Wi-Fi antenna cables allows for a more thorough disassembly and access to various aspects of the Classmate PC.

🔧 Step 12: Removing Screws Under the Rubber Feet

Flip the Classmate PC over to find four rubber feet on the underside. Underneath these rubber feet, you will discover screws holding the case together. Pry out these screws using precision flathead screwdrivers or needle-nose pliers. Remember, these screws can easily slide back into place during reassembly.

🔧 Step 13: Disconnecting the Speaker Cable

To fully separate the Classmate PC's components, disconnect the speaker cable from the motherboard. Carefully pull out the cable from its connector. Exercise caution and gentleness while performing this step to prevent any accidental damage.

🔧 Step 14: Disconnecting the Ribbon Cables

At this point, you will encounter two ribbon cables connecting the motherboard with other components. Referring back to when you removed the keyboard, lift the black plastic piece and detach the ribbon cables by sliding them out vertically. This will minimize any hassle during reassembly.

🔧 Step 15: Pulling Out the Motherboard

With all the necessary components detached, gently maneuver the motherboard until it can be fully removed from the Classmate PC. Take note of any screws or additional connectors that may still be securing the motherboard in place. Exercise caution and patience during this step to avoid any damage.

Congratulations! You have successfully disassembled the Classmate PC from First Team FRC,612. Remember to store the removed screws and parts in a safe place for reassembly. If you have any questions or require further assistance, please don't hesitate to reach out.

[Resources]

• Website: First Team FRC,612